cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
SINUMERIK 840D PLC 用户报警详解:700000 段报警号 → DB2 位地址换算 + 自定义报警文本制作-CNCShare | 数控电气技术中心

SINUMERIK 840D PLC 用户报警详解:700000 段报警号 → DB2 位地址换算 + 自定义报警文本制作

840D PLC 用户报警 700000 段怎么查?本文给出 700xxyy → DB2.DBX 位地址换算公式(含 700806→244.6 算例)、用户区 0–9 地址速查表、UDT2/UDT1002 选型、FC10 的 ToUserIF 用法、ALARM_S/SQ...
FANUC SERVO GUIDE: Waveform Analysis, Vibration Suppression and Rigid Tapping-CNCShare | 数控电气技术中心

FANUC SERVO GUIDE: Waveform Analysis, Vibration Suppression and Rigid Tapping

A field guide to FANUC SERVO GUIDE: what it does, which controls it supports, how to install and connect over Ethernet, and the four workflows that solve most servo problems.
前天
0826
Heidenhain Touch Probe Calibration: iTNC 530 Uses MP, TNC 640/TNC7 Uses Cfg — Calibrate in the Right Place-CNCShare | 数控电气技术中心

Heidenhain Touch Probe Calibration: iTNC 530 Uses MP, TNC 640/TNC7 Uses Cfg — Calibrate in the Right Place

The complete Heidenhain touch probe calibration and in-machine measurement reference: the iTNC 530 versus TNC 640/620/TNC7 parameter generations, 3-D and touch-trigger probe calibr...
前天
08115
FANUC 模拟主轴调试全流程:8133#5/3716#0/3717 启用链 + 3730/3731 电压标定 + JA40/JA41 接线-CNCShare | 数控电气技术中心

FANUC 模拟主轴调试全流程:8133#5/3716#0/3717 启用链 + 3730/3731 电压标定 + JA40/JA41 接线

模拟主轴的坑不在参数多,而在启用链顺序错、3730 与 3731 填反、JA41 编码器 A/B 接错。本文按接线→启用链→电压标定→功能验证四步走:给出 3717 填 0 时无报警却不转的原因、3731 先 3730 ...
SINUMERIK 828D User Alarm Bits: DB1600 Sequential Mapping and Extended 701000-701999-CNCShare | 数控电气技术中心

SINUMERIK 828D User Alarm Bits: DB1600 Sequential Mapping and Extended 701000-701999

The SINUMERIK 828D user alarm bit address reference: the DB1600 sequential mapping contrasted item by item with the 840D DB2 grouped algorithm (700247 is DB1600.DBX30.7 on the 828D...
3天前
0797
SINUMERIK 828D/840D 轮廓误差与跟随误差调参:25050 报警、Kv 因子、前馈、摩擦补偿与圆度测试(附参数速查表)-CNCShare | 数控电气技术中心

SINUMERIK 828D/840D 轮廓误差与跟随误差调参:25050 报警、Kv 因子、前馈、摩擦补偿与圆度测试(附参数速查表)

25050 轮廓监控报警怎么调?本文按西门子官方口径讲透 SINUMERIK 828D/840D 跟随误差与轮廓误差的调参顺序:三个监控报警的阶段区别、Kv 因子 MD32200 与跟随误差的定量关系、前馈 MD32620 系列...
华中数控 HNC 报警代码速查表:真实系统报警只有 13 条(01h–44h),网传「E001–E239」是自编号-CNCShare | 数控电气技术中心

华中数控 HNC 报警代码速查表:真实系统报警只有 13 条(01h–44h),网传「E001–E239」是自编号

查华中报警前先纠正一个数:官方系统内部硬件报警只有 13 条,不是网上写的 14 条,全部 h 结尾(01h–44h)。本页逐条核实 13 条的含义、系统状态与处理措施,点破网传 E001–E239 的三处自相...
FANUC Program Transfer: RS-232, Memory Card, USB, Ethernet and DNC — Pinout, Parameters and Troubleshooting-CNCShare | 数控电气技术中心

FANUC Program Transfer: RS-232, Memory Card, USB, Ethernet and DNC — Pinout, Parameters and Troubleshooting

Transferring a program into a FANUC control fails for four recurring reasons: wrong cable pinout, wrong 0020 I/O channel, mismatched serial frame settings, or a media format the co...
7天前
0795
SINUMERIK 828D 循环报警 61000/62000/65xxx 怎么查?六位号段判定 + 61000 无刀补 + 循环参数校验排错-CNCShare | 数控电气技术中心

SINUMERIK 828D 循环报警 61000/62000/65xxx 怎么查?六位号段判定 + 61000 无刀补 + 循环参数校验排错

828D 的 61000/62000 是六位报警号 06xxxx 段的简写,两者同属西门子标准循环报警;065000–069999 才是用户循环报警。本文给号段判定表、61000「无刀具补偿激活」的含义、从报警文本到循环参数...
How to Use FANUC One-Touch Setting & Servo Initialization - Parameter Setting Support (8130/1010/1020/1023) + SV SET (2020/2000#1/1820/2084-2085)-CNCShare | 数控电气技术中心

How to Use FANUC One-Touch Setting & Servo Initialization – Parameter Setting Support (8130/1010/1020/1023) + SV SET (2020/2000#1/1820/2084-2085)

FANUC One-Touch Setting (Parameter Setting Support) sets axis count/name/assignment at once; Servo Initialization (SV SET) computes pulses/gear/direction from motor ID 2020; FSSB a...
21天前
0798
广告合作 / 商务合作