FANUC 全闭环改半闭环(临时屏蔽光栅尺)完整流程:1815#1 / 2024 / 2084/2085 / 2185 + 改完三步验证(附各机型参数口径差异)
FANUC 光栅尺故障怎么临时屏蔽改半闭环?逐项讲清 1815#1/1815#5、2024、2084/2085、2185、1821、1850、1851/1852、2003#5、2019#7 的切换口径,明确指出 2185 与 2024 各来源冲突、必须按本机...
FANUC MPG Handwheel Not Working? Signal-Chain Troubleshooting: Servo Ready, I/O Link Assignment, Parameter Priority
FANUC handwheel (MPG) not working? Check in a fixed order: αi amplifier LED showing 0 = servo ready, HA/HB waveform and 5 V, I/O Link 16-byte OC02I assignment and the JA3 either/o...
How to Configure an Analog Spindle / Analog Axis on SINUMERIK 828D: MD30100–31050, X252 Wiring, MD32250/32260 Scaling
When an 828D drives an inverter or analog drive, the axis must be configured as an analog (analog setpoint output) axis rather than a digital one. This guide gives the values for M...
SINUMERIK 828D External Programs / DNC: EXTCALL Syntax, Running from CF/USB, Network Online
The 828D has limited NC memory, so large mould programs are either copied in, executed from external memory, or run online over the network. This covers EXTCALL drive letters and t...
FANUC PMC Project From Scratch: The 6-Stage Flow From Backup to Download to Verification
A complete FANUC PMC project in six stages: site survey, full backup, address planning, safety-first logic, online download, staged verification. Plus the five things to hand over ...
Fanuc Servo Resonance and Notch Filter Setup: Finding the Frequency with Servo Guide
A squealing servo is not fixed by just lowering the gain. Based on the official FANUC servo tuning manual and the HRV filter notice: separating resonance from mechanical impact, re...
Fanuc PMC Alarm Codes Explained: How to Read, Search and Clear a PMC Fault
How to read, search and clear Fanuc PMC alarm codes without losing your ladder.
828D 第三个手轮 / Mini HHU 怎么接?MD11350 + FB1 + DB11/DB21/DB31
前两个手轮走 X143,第三个走 MCP 的 X60;828D 的 MD11350=5 与 840D sl PROFINET MCP 的 =7 不能混用。讲清三个 MD、FB1 RUN_UP 必填参数、PLC 三区信号,以及手轮转而轴不动最常见的原因。
FANUC Alarm 459 HI HRV Setting Error: Odd/Even Axis-Pair SVM Mismatch (Root Cause & Fix)
FANUC alarm 459 'HI HRV SETTING ERROR' is raised when two axes whose servo axis numbers (parameter 1023) are an odd/even pair have mismatched high-speed HRV capability — one SVM s...
撞刀了怎么查原因?保现场 + 机械/参数/程序三分排查 + 撞后复校与防撞四件套
撞刀后先保现场:别回零、别清报警、别动工件、别改参数,拍三张照片记 G54 与刀补。再按机械/参数坐标系/程序操作三分排查,最后回零对刀空运行复校,并用对刀仪、仿真、软限位、首件单段四件...



















