cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
SINUMERIK 840D sl Alarm Code Quick Reference: Number Ranges, Reactions and Manual Index-CNCShare | 数控电气技术中心

SINUMERIK 840D sl Alarm Code Quick Reference: Number Ranges, Reactions and Manual Index

840D sl alarms are six-digit numbers; the full per-number text lives only in the official Siemens diagnostics manual. This page gives the number ranges, CN/EN reaction terms, how t...
5天前
05015
Fanuc CNC Specifications Comparison: 0i-MF vs 30i-B vs 31i-B vs 32i-B vs 35i-B, Two Official Data Sets-CNCShare | 数控电气技术中心

Fanuc CNC Specifications Comparison: 0i-MF vs 30i-B vs 31i-B vs 32i-B vs 35i-B, Two Official Data Sets

Is the 30i-B a 96-axis or a 40-axis control? Both figures are official, from two generations of Fanuc literature. Two data sets side by side, a fourteen-item verification framework...
5天前
05012
电气原理图 ↔ I/O 分配表 ↔ PMC 梯形图三方对照:从报警反查到端子和元件的完整路径-CNCShare | 数控电气技术中心

电气原理图 ↔ I/O 分配表 ↔ PMC 梯形图三方对照:从报警反查到端子和元件的完整路径

现场最费时的故障往往是图纸、地址表和梯形图三份资料对不上。本页讲清三方的职责边界与换算关系,给出从报警文本分类、A/D 地址、梯形图触点到 I/O 端子和电气图纸的完整反查链,以及找不到触...
发那科梯形图保持型地址:哪些断电不丢 R DR E EP-CNCShare | 数控电气技术中心

发那科梯形图保持型地址:哪些断电不丢 R DR E EP

一句话答案:发那科 PMC 地址并非一律断电就丢:R(保持型继电器)是主力,DR/E/EP 也属保持型,而 K/D/A 容易与 R 混淆;分清地址的断电保持特性才能避免「重启就出问题」的隐蔽故障。本文讲清...
Fanuc Canned Cycle Parameter Table: Address Words, Parameters 5121/5213 and Related Alarms-CNCShare | 数控电气技术中心

Fanuc Canned Cycle Parameter Table: Address Words, Parameters 5121/5213 and Related Alarms

A citable FANUC canned-cycle reference: nine cycles x address words x parameters x alarms, four-way, with an anchor on each row. Covers the nine-cycle master table, X/Y/Z/R/Q/P/F/K...
前天
05015
828D 与 S7-1200/1500 通讯怎么配?PN/PN Coupler 循环 I/O 与 S7 GET/PUT 别混着查-CNCShare | 数控电气技术中心

828D 与 S7-1200/1500 通讯怎么配?PN/PN Coupler 循环 I/O 与 S7 GET/PUT 别混着查

PN/PN Coupler 走 PROFINET 循环 I/O 映射,GET/PUT 走 S7 单边连接,是两条不同层次的路线。本页给出官方可核实的配置顺序、X1/X2 分网、MD12986 与字节扩展版本门槛,以及联调核对清单。
Why Is a Fanuc Parameter Missing? Four Hiding Mechanisms and a Five-Step Field Check-CNCShare | 数控电气技术中心

Why Is a Fanuc Parameter Missing? Four Hiding Mechanisms and a Five-Step Field Check

A parameter listed in the manual but absent on the control is usually not lost. Option entitlement versus visibility, axis-count filtering, generation differences, write protection...
7天前
0508
FANUC 全闭环改半闭环(临时屏蔽光栅尺)完整流程:1815#1 / 2024 / 2084/2085 / 2185 + 改完三步验证(附各机型参数口径差异)-CNCShare | 数控电气技术中心

FANUC 全闭环改半闭环(临时屏蔽光栅尺)完整流程:1815#1 / 2024 / 2084/2085 / 2185 + 改完三步验证(附各机型参数口径差异)

FANUC 光栅尺故障怎么临时屏蔽改半闭环?逐项讲清 1815#1/1815#5、2024、2084/2085、2185、1821、1850、1851/1852、2003#5、2019#7 的切换口径,明确指出 2185 与 2024 各来源冲突、必须按本机...
FANUC MPG Handwheel Not Working? Signal-Chain Troubleshooting: Servo Ready, I/O Link Assignment, Parameter Priority-CNCShare | 数控电气技术中心

FANUC MPG Handwheel Not Working? Signal-Chain Troubleshooting: Servo Ready, I/O Link Assignment, Parameter Priority

FANUC handwheel (MPG) not working? Check in a fixed order: αi amplifier LED showing 0 = servo ready, HA/HB waveform and 5 V, I/O Link 16-byte OC02I assignment and the JA3 either/o...
7天前
04912
How to Configure an Analog Spindle / Analog Axis on SINUMERIK 828D: MD30100–31050, X252 Wiring, MD32250/32260 Scaling-CNCShare | 数控电气技术中心

How to Configure an Analog Spindle / Analog Axis on SINUMERIK 828D: MD30100–31050, X252 Wiring, MD32250/32260 Scaling

When an 828D drives an inverter or analog drive, the axis must be configured as an analog (analog setpoint output) axis rather than a digital one. This guide gives the values for M...
21天前
04910
广告合作 / 商务合作