cncshare的头像-CNCShare | 数控电气技术中心
共享屋江苏管理员
每天进步一点点
FANUC Spindle Gear Shifting: 3705/3732/3735/3741-3744/3751-3753/4056-4059 and PMC Signals-CNCShare | 数控电气技术中心

FANUC Spindle Gear Shifting: 3705/3732/3735/3741-3744/3751-3753/4056-4059 and PMC Signals

Gear-shift setup breaks most often because the clamp-speed parameter names are confused (there is no 3734; minimum is 3735, maximum 3736), 3741-3744 is inverted against the gear ra...
6天前
0516
FANUC 换刀卡死怎么强制解开?机械手卡死 / 刀套不落位的四种手动恢复法(PMC 强制输出、电磁阀强给 24V、机械泄压、电机盘车)-CNCShare | 数控电气技术中心

FANUC 换刀卡死怎么强制解开?机械手卡死 / 刀套不落位的四种手动恢复法(PMC 强制输出、电磁阀强给 24V、机械泄压、电机盘车)

换刀已经卡死时的救援动作,不是排查流程。先按六个断点分型定位,再按侵入深度从浅到深依次上手段:PMC 强制输出(普通 FORCE 需停 PMC,X/Y 自锁强制 OVERRIDE 不用停)→ 电磁阀脱离 PLC 直...
SINUMERIK Servo Alarms 25000, 25010 and 25201: Which Layer to Troubleshoot First-CNCShare | 数控电气技术中心

SINUMERIK Servo Alarms 25000, 25010 and 25201: Which Layer to Troubleshoot First

SINUMERIK three-code triage: 25000/25010 are NCK measuring-system alarms, while 25201 is the NC relaying a SINAMICS drive fault whose real cause is a drive-side F code. Includes a ...
3天前
05113
CNC 报警号形态识别卡:FANUC / SINUMERIK / 三菱 M80 / HEIDENHAIN 位数、前缀与号段对照(30 秒定位该翻哪本手册)-CNCShare | 数控电气技术中心

CNC 报警号形态识别卡:FANUC / SINUMERIK / 三菱 M80 / HEIDENHAIN 位数、前缀与号段对照(30 秒定位该翻哪本手册)

看到一个报警号,先判断它是哪个系统的。本页只做入口识别:四品牌报警号的位数、前缀与号段形态、该去哪个画面查、翻哪本手册、站内哪篇速查页对得上,附 6 位号分流法。
FANUC M98 / M99 子程序怎么调用?P 号规则、嵌套上限与 076 / 077 / 078 三个报警怎么查-CNCShare | 数控电气技术中心

FANUC M98 / M99 子程序怎么调用?P 号规则、嵌套上限与 076 / 077 / 078 三个报警怎么查

FANUC M98/M99 子程序调用全解:P 号四种写法、L 重复次数、NC 侧 M98 与 PMC 侧 SUB 的边界、M99 三种用法,并明确指出 077 嵌套上限在三份资料里写 3 重/5 层/8 层互相冲突、必须按本机手册。...
FANUC Alarm Code List: P/S Alarms 5130–5559 Explained (Part 6)-CNCShare | 数控电气技术中心

FANUC Alarm Code List: P/S Alarms 5130–5559 Explained (Part 6)

English reference for FANUC P/S alarm numbers 5130 to 5559: PMC axis overlap, flexible synchronous control, tool management and interference, Cs contour control, tilted surface mac...
22天前
0515
Fanuc Canned Cycle Parameter Table: Address Words, Parameters 5121/5213 and Related Alarms-CNCShare | 数控电气技术中心

Fanuc Canned Cycle Parameter Table: Address Words, Parameters 5121/5213 and Related Alarms

A citable FANUC canned-cycle reference: nine cycles x address words x parameters x alarms, four-way, with an anchor on each row. Covers the nine-cycle master table, X/Y/Z/R/Q/P/F/K...
前天
05015
828D 与 S7-1200/1500 通讯怎么配?PN/PN Coupler 循环 I/O 与 S7 GET/PUT 别混着查-CNCShare | 数控电气技术中心

828D 与 S7-1200/1500 通讯怎么配?PN/PN Coupler 循环 I/O 与 S7 GET/PUT 别混着查

PN/PN Coupler 走 PROFINET 循环 I/O 映射,GET/PUT 走 S7 单边连接,是两条不同层次的路线。本页给出官方可核实的配置顺序、X1/X2 分网、MD12986 与字节扩展版本门槛,以及联调核对清单。
Why Is a Fanuc Parameter Missing? Four Hiding Mechanisms and a Five-Step Field Check-CNCShare | 数控电气技术中心

Why Is a Fanuc Parameter Missing? Four Hiding Mechanisms and a Five-Step Field Check

A parameter listed in the manual but absent on the control is usually not lost. Option entitlement versus visibility, axis-count filtering, generation differences, write protection...
7天前
0508
Fanuc Servo Amplifier Alarm Codes: Full A06B 7-Segment Table and Dotted IPM Codes-CNCShare | 数控电气技术中心

Fanuc Servo Amplifier Alarm Codes: Full A06B 7-Segment Table and Dotted IPM Codes

Split the table by A06B series, then use plain 8/9/A overcurrent versus dotted 8./9./A. IPM to decide between testing the motor cable and opening the drive.
11天前
0509
广告合作 / 商务合作