FANUC 固定循环怎么用?G81 / G82 / G83 / G73 / G84 / G85 / G86 / G87 / G88 九个循环一张表选对 + Q/R/P/K 地址字 + 参数 5121/5213 + 045 报警根因
固定循环是 FANUC 编程里一行代码干一串动作的功能,也是新手最容易出事的地方。本篇讲清三个模态 G90/G91、G98/G99、G80 的区别,九个循环 G81-G88 的选用,Q/R/P/K 地址字写法,G73 与 G83 的...
How to Clear All Parameters on a Fanuc Control: RESET + DELETE Power-On Sequence Explained (and Why “Restore Factory Settings” Does Not Exist)
A good half of the 'Fanuc restore factory settings' tutorials are wrong: there is no such menu on a 0i-MD / 0i-MF. The real entry is a hardware key combo - power down, hold RESET +...
FANUC Main Board Spare Numbers: A16B / A17B / A20B Board Families and 5 Things to Check Before Swapping
Circulated tables like 'A20B-8100-0135 = 0i-A, -0450 = 0i-B, -0660 = 0i-C' come from different spare vendors who conflict with each other. Labeled as circulated field lists to veri...
FANUC LADDER III: Compile, Decompile and Program Protection Explained
Why FANUC LADDER III needs compile and decompile: compile to download or monitor online, decompile to edit or analyze an uploaded program. Plus how ladder program password protecti...
828D 刀库管理初始化怎么配?Mag_conf.mpf 与 9998/9999
828D 刀库初始化不是改一个参数,是把真实刀库、缓冲区 9998、装刀点 9999 三者的关系一次性写进系统。讲清 Mag_conf.mpf 七个变量、MD22550 在链式与圆盘的取值差异、两条生效路径与初始化后必...
FANUC 459 报警(HI HRV 设定错误)怎么处理:奇-偶轴对 SVM 不一致的根因与排查步骤
FANUC 报警 459「HI HRV SETTING ERROR / 高速 HRV 设定错误」由伺服轴号(参数 1023)相邻的奇-偶轴对引起:一台 SVM 支持高速 HRV、另一台不支持。本文讲清根因、定位方法、处理步骤,并区分 ...
FANUC M98 / M99 子程序怎么调用?P 号规则、嵌套上限与 076 / 077 / 078 三个报警怎么查
FANUC M98/M99 子程序调用全解:P 号四种写法、L 重复次数、NC 侧 M98 与 PMC 侧 SUB 的边界、M99 三种用法,并明确指出 077 嵌套上限在三份资料里写 3 重/5 层/8 层互相冲突、必须按本机手册。...
FANUC Alarm Code List: P/S Alarms 5130–5559 Explained (Part 6)
English reference for FANUC P/S alarm numbers 5130 to 5559: PMC axis overlap, flexible synchronous control, tool management and interference, Cs contour control, tilted surface mac...
SINUMERIK 840D sl 报警代码一览表:NCK / 循环 / HMI / SINAMICS / PLC 五区号段
840D sl 报警是六位号。按官方诊断手册号段定归属,再读清除条件决定要不要断电;纠正「4xxxx = 机床数据」与「700000 归西门子」两处误读。
FANUC PMC 扫描周期怎么导致信号漏采、定时器提前:中文现场排查
按钮按了有时没反应、接近开关到位触点偶尔不亮、定时器没到时间就动作——这类偶发问题多半与 PMC 扫描周期有关。本页讲清输入—执行—输出四阶段、扫描时间以本机诊断画面为准、四类典型现象...



















