FANUC 16i / 18i / 21i / 30i / 31i 怎么区分?型号识别、轴数口径与备件选型一次说清
机库里一台老 FANUC,面板只写着「18i」,到底是哪一代、几轴、能不能互换备件?本页按官方 Descriptions 手册(B-63002EN / B-63522EN)核实轴数口径——中文常引的「16i 8轴6联动、18i 6轴4联...
数控报警号形态与号段总索引:FANUC / 西门子 / 三菱 / 海德汉 / 华中 / 广数 / 新代 / 科德 八品牌对照 + 这条报警该找谁
一条报警拿在手里,第一个问题不是「怎么修」,而是「这条报警归谁管」。本页把八个品牌的报警号形态放进速辨卡,把每段号归到子系统,再加「该找谁」分流列。国产四品牌站内首次成表,华中官方...
Five Peripheral Alarm Clusters on CNC Machines: Coolant, Lubrication, Chip Conveyor, Air and Hydraulics – From English Alarm Text to PMC Feedback to Action
Coolant, lubrication, chip conveyor, pneumatic and hydraulic alarms are usually written by the machine tool builder in the PMC/PLC, not by FANUC or Siemens. A cross-system matrix o...
海德汉 TNC 固定循环参数速查表:Cycle 200/203/230/251/252/256/257/4xx/48x 逐个 Q 参数含义 + 与 FANUC G 循环迁移
海德汉 TNC 固定循环 Q 参数速查:钻孔族 200-209、型腔铣 230/251/252、探测 4xx、刀具测量 48x 逐条 Q 参数含义,纠正 Q212/Q213 网上错写,附 FANUC G 循环功能迁移对照。参数按 iTNC530/TNC...
828D / 840D sl ↔ FANUC ↔ 三菱 M80 常用参数三方对照总表(按功能对齐,不按号段对齐)
828D/840D sl、FANUC、三菱 M80 三方参数对照总表:轴/软限位/反向间隙/主轴/零点/润滑/滤波/伺服整定按功能横排,每行带 par-* 深链锚点。三套编号体系互不相通,仅作功能对照与检索入口,参数...
机床为什么要预热?热变形与首件精度漂移:三处热源 + 20 分钟预热协议 + 主轴油温与环境温度设定 + 热伸长诊断方法
机床预热与热变形全解:三处热源地图、两个方向性判据、20 分钟分档预热协议、千分表热平衡判定、主轴油冷机低 2–3℃ 设定、软件补偿不能替代预热的边界与设备台账化。数值按本机手册与实测热...
SINAMICS F 码 ↔ SINUMERIK 828D / 840D sl 显示号 四向对照总表:F 码 / 230xxx 六位号 / 故障原因 / 首选检查动作(每条可链)
手册写 F30020、828D 屏上显示 230020,同一故障两套编号。本页把 SINAMICS F 码与 828D/840D sl 显示号、故障原因、首选检查动作四向并排,覆盖 F300xx 功率单元族、F07011/F31100 驱动与编码...
FANUC Alarm Code List: P/S Alarms 0492–1308 Explained (Part 3)
English reference for FANUC P/S alarm numbers 0492 to 1308: 3D interference check, Cs contour control, thread cutting, macro syntax and variables, program registration, and G10 par...
HEIDENHAIN TNC Fixed Cycle Parameter Reference: Cycle 200/203/230/251/252/4xx Q Parameters and FANUC G-Cycle Migration
HEIDENHAIN TNC fixed cycle Q-parameter reference: drilling 200-209, pocket milling 230/251/252, probing 4xx, tool measurement 48x with per-cycle Q meanings. Corrects the Q212/Q213 ...
FANUC M98 / M99 Subprogram Calls: P Numbers, Nesting Limits and How to Troubleshoot Alarms 076 / 077 / 078
FANUC M98/M99 subprogram calls explained: four P-number formats, L repeat counts, the boundary between NC M98/M99 and PMC SUB, three uses of M99, and the conflicting nesting limits...



















