快速入门学习数控机床电气技术

进口数控机床维修常见机床报警中英文对照

进口数控机床维修常见机床报警中英文对照

T CODE ERROR (T 码错误)LOW OIL LEVEL (油位低)SPINPLE FAULT (主轴故障)SPINDLE ALARM (主轴报警)

EXTERNAL EMG STOP (急停按钮被按下)

AC NOT READY (交流盘未准备好)

SPINPLE LUBE FAULT (主轴润滑故障)

T CODE ERROR (T代码出错,非法T代码)

M CODE ERROR (M代码出错,非法M代码)

SERVO NOT READY (伺服未准备好)

NC NOT READY(NC没准备好)

TURRET FAULT (转塔故障)

TURRET LIMIT (转塔限位)

DC 24V OPEN (直流24断开)

+24V NOT READY(+24V没准备好)

GRAR DRIFT (档位漂移)

PLEASE AXIS RETURN HOME(轴未回零)

PLEASE DRUM RETURN HOME(刀库未回零)

AIRPRESSFAILURE(气压故障)

UNCL TOOL FALL(松刀失败)

AIR PRESSURE DROP (压缩空气压力过低)

CLAMP TOOL FALL(夹刀失败)

DRUM NOT PARKED(刀库未在原值)

X ZERO POINT NOT REACHED (X 轴未回零)

Y ZERO POINT NOT REACHED (Y 轴未回零)

Z ZERO POINT NOT REACHED (Z 轴未回零)

4TH ZERO POINT NOT REACHED (第4轴未回零)

X AXIS OVERTRAVL(X轴超限)

Y AXIS OVERTRAVL (Y轴超限)

Z AXIS OVERTRAVL (Z轴超限)

COUNTER SWITCH REEOR (计数开关故障)

MASTERT RANSFER OVER TEMP (主变压器过热)

Z AXIS NOT AT FIRST REF POSITION (Z轴未在第一参考点)

SPINDLE ORIENTATION FALLURE (主轴定向失败)

TOOL DESENT OR TOOL DATA REEOR (刀具数据错误)

PLEASE UNLOAD THE TOOL ON SPRINELK (请卸下主轴上的刀)

PLEASE LOAD TOOL ON APINDLE (请装上主轴上的刀)

A AXIS UNCLAMP FAIL (A 轴松开失败)

A AXIS CLAMP FAIL (A 轴夹紧失败)

DRUM OUT TO APRONDLEIS FALL (刀库摆向换刀位失败)

MG SWING OVERLOAD(刀库摆动过载)

DRUM BACK PARK IS FALL (刀库摆回原始位失败)

TURRENT MOTOR1 OVERLOAD (刀库移动电机过载)

COOLANT MOTOR OVERLOAD (冷却泵过载)

DRUM ATC FAULT (自动换刀失败)

TOOLS UNLOCKED (刀具未锁紧)

BATTERY ALARM (电池报警)

DRUM POSITION SWITCH ERROR (刀库位置检测开关故障)

DRUM NOW NOT AT PARK (刀库未在原始位置)

IT DANGOU TO MOVE DRUM (刀库禁动)

POT UO FAILOR POT NOT AT UP POSITION (刀套未在水平位)

POT DOWN FAIL (刀套翻下动作失败)

IT IS DANGOUR TO MOVE ARM (机械手禁动)

THE SPINDLE STATU IS ERROR (主轴状态错误)

ARM MOTOR OR ARM SWITCH FALL (机械手或机械手开关故障)

CENTRE LUBRICATION FALL (中心润滑故障)

THE WORK NOT CLAMPED (工件未夹紧)

AUTO TOOL CHANGE FAULT (自动换刀失败)

TOOL DATA OUT OF RANGE (指令刀具号超出范围)

THE ORDER TOOL NOW IN SPINDLE (目标刀具在主轴上)

THE THREE SPINDLE SWITCH FAULT (主轴上的接近开关)

THE CENTRE COOLANT IS LOWER (刀具内冷泵液位过低)

DRUM RETURN 1# POSITION FAULT (刀库自动回零失败)

SPINDLE OVERLOAD (主轴过载)

关注我们的微信公众号shukongzhpngguo,获取更多数控技术文章。

TURRENT MOTOR OVERLOAD (刀盘转动电机过载)

CHIP CONVEYER OVERLOAD (拉屑器过载)

HARD LIMIT OR SERVO ALARM (硬限位或伺服报警)

NO LUB OIL (无润滑油)

INDEX HEAD UNLOCKED (分度头未锁紧)

MT NOT READY(机床没准备好)

MG OVERLOAD  (刀库过载)

LUB EMPTY(润滑无油)

AIR PRESSURE(气压不足)

COOLANT NOT READY(冷却没准备好)

LUBE EMPTY(油雾油位低,润滑油位低)

LUB PRESSURE LOW(润滑压力低)

CONVEY  VERLOAD(排屑过载)

LUB OVERLOAD(润滑过载)

LUBE PRESSURE LOW(油雾压力低)

SERIAL SPINDLE ALARM (串行主轴报警)

NC BATTERY LOW ALARM(NC电池低报警)

MAGAZINE MOVE LIMIT SWITCH ERROR

SPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR

MAGAZINE NOT IN POSITION OR SENSOR ERROR

AIR PRESSURE LOW ALARM(气压低报警)

MOTOR OVERLOAD(电机过载)

T CODE > MAGAZINE TOOLS

T CODE < 1 ERROR

5TH AXIS HARDWARE OVERTRAVER LIMIT ERROR

DOOR IS OPENED(开门)

LUB PRESSURE SWITCH ERROR(油压开关错误)

SPINDLE OIL COOLANT UNIT ERROR

SPINDLE LOAD ABNORMAL(主轴负荷异常)

TRANSDUCER ALARM(传感器报警)

BED-HEAD LUBRICATE OFF(床头润滑关闭)

EMG OFF

HYDRAULIC CHUCK PRESS LOW(液压夹头压力低)

HYDRAULIC TAIL PRESS LOW(液压尾座压力低)

LUB 0IL LOW(油压低)

TURRET CODE ERROR(转塔码错误)

TURRET RUN OVERTIME(转塔运行超时)

MANUAL HANDLE INTERRUPT

TRY TO RUN SPINDLE WHILE CHUCK NOT LOCK

TRY TO RUN SPINDLE WHILE TAIL NOT LOCK

SPINDLE NEUTRAL GEAR

MAGAZINE ADJUST

HYDRAULIC NOT RUN

SAFETY DOOR BE OPENED

SAFETY DOOR NOT CLOSE

NOT ALL AXIS HAVE GONE BACK REF

IN ADJUST,IGNORE GOING BACK REF

AFTER EXCHANGE TOOL,CYCLE START

ATC MOTOR QF16 OFF

X AXIS IS LOCKED(X 轴被锁定)

Y AXIS IS LOCKED(Y 轴被锁定)

Z AXIS IS LOCKED(Z 轴被锁定)

A AXIS IS LOCKED(A 轴被锁定)

SPINDLE MOTOR FAN QF26 OFF(主轴电机风扇QF26关闭)

关注我们的微信公众号shukongzhpngguo,获取更多数控技术文章。

SPINDLE ORIENTATION INCOMPLETE(主轴定位不完全)

M FUNCTION NOT COMPLETE(M 功能无法完成)

SPINDLE NOT IN GEAR POSITION(齿轮不在主轴位置)

SPINDLE NOT CHANGED TO LOW GEAR(主轴没有变为低档)

SPINDLE NOT CHANGED TO HIGH GRAR(主轴没有变为高档)

MAG NOT BACKWARD

SPINDLE TOOL NOT CLAMP

SPINDLE TOOL NOT UNCLAMP

MAG NOT IN POSITION

MAG DOES NOT ROTATE

MAG DOES NOT STOP RUNNING

A AXIS HAVE NOT CLAMPED

A AXIS HAVE NOT UNCLAMPED

SET D499=1,”MAG.JOG” SWITCH ON

HYDRAULIC MOTOR QF7 OFF( 液压马达QF7关闭 )

HYDRAULIC TEMPRETURE HIGH( 液压使用温度高 )

HYDRAULIC FILTER BLOCKED(液压过滤器阻止)

HYDRAULIC OIL LEVEL LOW( 液压油位低 )

HYDRAULIC FAN QF8 OFF(液压风扇QF8关闭)

HELIX CONYER QF9 OR QF10 OFF

转发到朋友圈吧,你的朋友也在找这篇文章呢!

秒懂FANUC PMC学习群第三期招生,随到随学


>>1、共享屋自动发货商店,学习数控机床电气资料软件、教程,点击进入
>>2、共享屋商店购买流程
© 版权声明
THE END
喜欢就支持一下吧
点赞14
分享
评论 抢沙发

请登录后发表评论